| TNZ 1 |
- |
Air filter element rods, solenoid wire attachment to starters |
|
|
|
| TNZ 2 |
- |
Alternator adjustment bolts, starter belt housing bolts and ground wires Astro van exhaust flange, Dodge alt bolt, starter bolt on trans, Buick Roadmaster Cadillac, Camaros, Ford [91 to 94], Jeep [91 to 99], Dodge trucks 90 to 04, Chevy trucks [1985 to 2005] |
|
|
|
| TNZ 3 |
- |
Used for TNZ 4 applications where the area is very tight such as passenger side motor mounts for manifold |
|
|
|
| TNZ 4 |
- |
Most versatile Toughnutz used on most vehicles from the manifold to the gas tank strap and starter mounting bolts |
|
|
|
| TNZ 5 |
- |
Camry flex pipe, Infinity, Cadillac, Chevy [12 models/12 engines 87 to 05] Chevy trucks [20 models/87 to 05], Ford trucks [90 to 2003 11 models/6 engines] Buick [12 models 86 to 2004], Olds [15 models/9 engines 86 to 03] |
|
|
|
| TNZ 6 |
- |
Toyota [25 models/10 engines 86 to 04], Camry catalitic converter, Acura [20 mods 11 engines 86 to 03 exhaust flange] |
|
|
|
| TNZ 7 |
- |
Camry exhaust mounting bolts |
|
|
|
| TNZ 8 |
- |
Used for TNZ 4 applications where a longer barrel is required |
|
|
|
| TNZ 9 |
- |
Most versatile weldable stud extender to be used with threaded rod to repair Y pipes and any other repairs where there is only a small bit of the stud left |
|
|
|
| TNZ 10 |
- |
Starter selinoid wire attachments |
|
|
|
| TNZ 11 |
- |
Gas tank threaded rod and other threaded rod attachments |
|
|
|
| TNZ 12 |
- |
Used on Chevrolet starters |
|
|
|
| TNZ 13 |
- |
Ground studs for Ford pickups, some hood height adjustments |
|
|
|
| TNZ 14 |
- |
Any 8mm 1.0 pitch threaded rod attachment, many makes and models Chevy trucks, GMC, Pontiac, Buick, Chevrolets |
|
|
|
| TNZ 15 |
- |
For use on Ford Focus, Mitsubishi Mirage, Toyota, and Chevy 3.1 |
|
|
|
| TNZ 16 |
- |
2002 power stroke Ford diesel starter, Ford master cylinder mounting bolts |
|
|
|
| TNZ 17 |
- |
Toyota Y pipes and manifolds |
|
|
|
| TNZ 18 |
- |
Used where TNZ 4 applications call for a thinner barrel wall is needed |
|
|
|
| TNZ 19 |
- |
Needed for many foreign truck procedures |
|
|
|
| TNZ 20 |
- |
Used to secure Ford coil packs where bolt has snapped |
|
|
|
| TNZ 22 |
- |
Used to secure coil packs on Toyota, Nissan, Honda, Chrysler, and some Trackers where the bolt has snapped |
|
|
|
| TNZ 50 |
- |
7/16" drill bit to be used to enlarge holes in cast iron and cast aluminum |
|
|
|
| TNZ 51 |
- |
1/2" drill bit to be used same as 7/16" drill bit, use cutting oil on both |
|
|
|
| TNZ 221 |
- |
Used to clean up the end of a stud so the Toughnutz will fit smoothly |
|
|
|
| TNZCGJT |
- |
Tool used to clean up a hole after enlargement, clean calipers of rust, clean slider pins after removing rubber, cleans holes for bearings of rust and many other uses |
